Red-lion LDA Manual do Utilizador descarregar pdf

AIR PRESSURE STABILIZATION VENT

(57.15)

2.25

GENERAL DESCRIPTION

The Large Display is a versatile display available as a DC volt, current, or

process meter with scaling, serial communications and dual relay outputs. The 5

digit displays are available in either 2.25" or 4" high red LED digits with

adjustable display intensities. The 2.25" high models are readable up to 130 feet.

The 4" high models are readable up to 180 feet. Both versions are constructed

of a NEMA 4X/IP65 enclosure in light weight aluminum.

All models also come with dual Form C relay outputs and RS232 / RS485

serial communications.

SAFETY SUMMARY

All safety regulations, local codes and instructions that appear in this and

corresponding literature, or on equipment, must be observed to ensure personal

safety and to prevent damage to either the instrument or equipment connected to

it. If equipment is used in a manner not specified by the manufacturer, the

protection provided by the equipment may be impaired.

ORDERING INFORMATION

MODEL NO. DESCRIPTION PART NUMBER

LD2A

2.25" High 5 Digit Red LED Volt/Current Meter w/

Relay Output and RS232/RS485 Serial Comms

LD2A05P0

LD4A

4" High 5 Digit Red LED Volt/Current Meter w/

Relay Output and RS232/RS485 Serial Comms

LD4A05P0

LD Plug Panel Meter Plug for LD models LDPLUG00

SPECIFICATIONS

1. DISPLAY: 5 digit, 2.25" (57 mm) or 4" (101 mm) intensity adjustable Red LED

(-99999 to 99999)

2. POWER REQUIREMENTS:

AC POWER: 50 to 250 VAC 50/60 Hz, 26 VA

DC POWER: 21.6 to 250 VDC, 11 W

DC Out: +24 VDC @ 100 mA if input voltage is greater than 50 VAC/VDC

+24 VDC @ 50 mA if input voltage is less than 50 VDC

Isolation: 2300 Vrms for 1 min. to all inputs and outputs

3. INPUT RANGES: Jumper Selectable

D.C. Voltages: 200 mV, 2 V, 20 V, 200 V, 10 V

INPUT

RANGE

ACCURACY @

23 °C LESS

THAN 85% RH

INPUT

IMPEDANCE

MAX

INPUT

SIGNAL

RESOLUTION

TEMP.

COEFFICIENT

200 mV 0.1% of span

1.033 MΩ

75 VDC 10 µV 70 ppm /°C

2 V 0.1% of span

1.033 MΩ

75 VDC 0.1 mV 70 ppm /°C

10 V 0.1% of span

1.033 MΩ

250 VDC 1 mV 70 ppm /°C

20 V 0.1% of span

1.033 MΩ

250 VDC 1 mV 70 ppm /°C

200 V 0.1% of span

1.033 MΩ

250 VDC 10 mV 70 ppm /°C

D.C. Currents: 200 µA, 2 mA, 20 mA, 200 mA

INPUT

RANGE

ACCURACY @

23 °C LESS

THAN 85% RH

INPUT

IMPEDANCE

MAX

INPUT

SIGNAL

RESOLUTION

TEMP.

COEFFICIENT

200 µΑ 0.1% of span

1.111 KΩ

15 mA 10 nA 70 ppm /°C

2 mA 0.1% of span

111 Ω

50 mA 0.1 µA 70 ppm /°C

20 mA 0.1% of span

11 Ω

150 mA 1 µA 70 ppm /°C

200 mA 0.1% of span

1 Ω

500 mA 10 µA 70 ppm /°C

D.C. Process: 4 to 20 mA, 1 to 5 VDC, 0/1 to 10 VDC

INPUT RANGE SELECT RANGE

4 - 20 mA Use the 20 mA range

1 - 5 VDC Use the 10V range

1 - 10 VDC Use the 10V range

4. OVERRANGE/UNDERRANGE INDICATION:

Input Overrange Indication: “OLOL”.

Input Underrange Indication: “ULUL”.

Display Overrange/Underrange Indication: “.....”/“-.....”

 2.25" & 4" HIGH RED LED DIGITS

 PROGRAMMABLE SCALING AND DECIMAL POINTS

 PROGRAMMABLE USER INPUT

 DUAL 5 AMP FORM C RELAY

 ALUMINUM NEMA 4X/IP65 CASE CONSTRUCTION

 RS232/RS485 SERIAL COMMUNICATIONS

 UNIVERSALLY POWERED

MODEL LD - LARGE DC VOLT/CURRENT/PROCESS DISPLAY

DIMENSIONS In inches (mm)

Bulletin No. LDA-E

Drawing No. LP0673

Released 04/13

Tel +1 (717) 767-6511

Fax +1 (717) 764-0839

www.redlion.net

CAUTION: Risk of Danger.

Read complete instructions prior to

installation and operation of the unit.

CAUTION: Risk of electric shock.

22 (558.8)

12 (304.3)

Z (Center)

7.875 (200)26 (660.4)LD4A05P0

4 (101.6)16 (406.4)LD2A05P0

Y (Height)X (Length)

PART

NUMBER

The protective conductor terminal is bonded to conductive

parts of the equipment for safety purposes and must be

connected to an external protective earthing system.

US LISTED

51EB

IND. CONT. EQ.

US LISTED

3RSD

PROCESS CONTROL EQUIPMENT

1 2 3 4 5 6 ... 15 16

Resumo do Conteúdo

Página 1 - DIMENSIONS In inches (mm)

1AIR PRESSURE STABILIZATION VENT(57.15)2.25XZYGENERAL DESCRIPTIONThe Large Display is a versatile display available as a DC volt, current, or process

Página 2 - 2.0 settIng the JuMpers

100.0tON-nON TIME DELAYEnter the time value in seconds that the output is delayed from turning on after the trigger point is reached. A value of 0.0

Página 3 - 3.0 WIrIng the Meter

11OUTPUTSTATEOFFONHysSPAutoOFFONOFFOFFONOFFONOFFOFFONOFFONOFFMANUALRESETLAtCHL-dLYSP - Hys( )( )( ){Setpoint Output Reset Action

Página 4 - 3.5 INPUT SIGNAL WIRING

Sending Serial Commands and DataWhen sending commands to the meter, a string containing at least one command character must be constructed. A command

Página 5 - 3.6 SERIAL WIRING

13Command Response TimeThe meter can only receive data or transmit data at any one time (half-duplex operation). During RS232 transmissions, the meter

Página 6 - 5.0 prograMMIng the Meter

14Communication FormatData is transferred from the meter through a serial communication channel. In serial communications, the voltage is switched bet

Página 7 - DESCRIPTION

15Setpoint ActionSetpoint SelectSetpoint ValueOutput Reset ActionHysteresis ValueO Time DelayOn Time DelayOutput Reset W/Display ResetSPSEL4-SPtAct-

Página 8 - LO-En LO-t FCS

LIMITED WARRANTYThe Company warrants the products it manufactures against defects in materials and workmanship for a period limited to two years from

Página 9

25. A/D CONVERTER: 16 bit resolutionA/D Conversion Rate: 6 readings/sec.6. DISPLAY RESPONSE TIME: 500 msec min.7. USER INPUT: Software selectable pull

Página 10

33.0 WIrIng the MeterEMC INSTALLATION GUIDELINESAlthough Red Lion Controls Products are designed with a high degree of immunity to Electromagnetic Int

Página 11 - PAr Addr Abbr

43.4 INPUT WIRING3.2 USER INPUT WIRINGCAUTION: Analog common is NOT isolated from user input common. In order to preserve the safety of the meter ap

Página 12

RS232 CommunicationsRS232 is intended to allow two devices to communicate over distances up to 50 feet. Data Terminal Equipment (DTE) transmits data o

Página 13 - Receiving Data From The Meter

6PROGRAMMING MODE ENTRY (PAR BUTTON)It is recommended all programming changes be made off line, or before installation. The meter normally operates in

Página 14 - Communication Format

7100.00dSP 2DISPLAY VALUE FOR SCALING POINT 2-19999 to 99999Enter the second Display Value by using the front panel buttons. This is the same for KE

Página 15 - Programming Mode

8Entering Code 66 will overwrite all user settings with the factory settings. The meter will display rESEt and then return to CodE 00. Press the PAR b

Página 16 - LIMITED WARRANTY

95.3 Module 3 - dIsplay and Front panel Button paraMeters (3-dSP)PARProFront Panel Display Select EnableDisplay Update TimeFront Pan

Comentários a estes Manuais

Sem comentários

Red-lion LDA Manual do Utilizador

Consulte online ou descarregue Manual do Utilizador para Hardware Red-lion LDA. Red Lion LDA User Manual Manual do Utilizador

Resumo do Conteúdo

Comentários a estes Manuais

Manuais e produtos relacionados com Hardware Red-lion LDA